Product Details
Company Profile

Low Impedance Antenna Microwave Sensor MC090S E

1. Features

1. Microwave motion detection version.

2. Eight DIP switch setting, distance, time, daylight sensor, multi-speed adjustable.

3. Ultra-small mounting size, multiple mounting options, support for top and bottom mounting options.

4. Super cost-effective, support a variety of lamps,tri-proof lamps, ceiling lamps.

5. The infrared sensor is used to filter out the light sensor, and the light sensitivity value is more accurate, and is not affected by cloudy and sunny days.

6. Low impedance 5.8G antenna for superior immunity to interference.

7. Batch over RED, TUV certification.

2. Parameter

Input	Operating Voltage Range	198-264VAC 50/60Hz
	DC Input Voltage	N/A
	Rated Voltage	220-240VAC 50/60Hz
	No-load Power	≤1.0W
	Stand-by Power	≤0.5W
	Surge Test	Between L and N: 1KV
Output	Working Mode	ON/OFF
	Type of Load	Resistive or Capacitive
	Load Capacity	800W (Resistive) or 400W (Capacitive)
	Current of Load	N/A
	Load surge current	30A relay - 30A (test twidth 500us @230Vac at 50% Ipeak, cold start at full load) or 60A (test twidth 200us @230Vac at 50% Ipeak, cold start at full load)
Interface	1-10V dimmer	N/A
	Synchronization control interface	N/A
	High and Low Level Interface	N/A
	PWM control interface	N/A
	Interface terminal wiring mode	N/A
Sensor	Operating Frequency	5.8 GHz ±74.9 MHz.ISM wave band
	Transmitting power	0.5mW Max.
	Hold time	5S/30S/60S/3min/5min/10min/20min/30min
	DIM down	N/A
	Cut off	N/A
	Detection Area	100% / 75% / 50% / 25%
	Daylight Sensor	2Lux/10Lux/25Lux/50Lux/Disable
	Daylight on/off	N/A
	Detecting Radius	4-7m (Installed at 3m high )
	Mounting Height	2.5-6 m(Suction Top Installation)
	Detecting Angle	Ceiling mount 150°
Wireless module	Operating Frequency	N/A
	Transmitting power	N/A
	transmission distance	N/A
	modulation mode	N/A
	Coding group number	N/A
Operating Environment	Operating Temperature	-20℃…+60℃ Humidity: 85% (non-condensing)
Operating Environment	Storage Temperature	-40℃…+80℃
Certificate Standards	Safety standards	EN61058-1
	EMC standards	EN300440, EN301489-1, EN55015, EN61547, EN61000-3-2, EN61000-3-3, EN62479
	Environmental Requirement	RoHS
	Certificate	CE, TUV & RED
Others	Input/output terminal specifications	0.5-0.75mm²
	IP Rating	IP20
	Protection Class	Class II
	Installation	Built-in installation
	Dimension	623625mm
	Package	Bubble bag + partition + outer box (K=A)
	Net Weight	36g
	Lifetime	50,000h @ Ta Full load
Note 1. “N/A”means not available. 2. Detection area is effected on volume of motion object and motion speed. The detection area is tested by a 165cm height person and walking speed is 0.5m/s.

3. Dimension (mm)

*The sensor is designed for connect one load only. Connect more than one loads may damage the sensor.

4. Radiation Pattern

Ceiling mounting

*50%,75%,100% detection sensitivity is workable when installed at 6m mounting height. Only 25% sensitivity is not able to detect motion signal.

Wall mounting:

5. Function Dialing Settings

Detection Area

	1	2
Ⅰ	ON	ON	100%
Ⅱ	ON	-	75%
Ⅲ	-	ON	50%
Ⅳ	-	-	25%

Hold Time

	3	4	5
Ⅰ	ON	ON	ON	5S
Ⅱ	ON	ON	-	30S
Ⅲ	ON	-	ON	1min
V	ON	ON	-	3min
IV	-	ON	ON	5min
IIV	-	ON	-	10min
ⅢV	-	-	ON	20min
IX	-	-	-	30min

Daylight Sensor

	6	7	8
Ⅰ	ON	ON	ON	2Lux
Ⅱ	ON	ON	-	10Lux
Ⅲ	-	ON	-	25Lux
V	ON	-	-	50Lux
IV	-	-	-	Disable

*When set to Disable gear, the sensor will turn on the light as long as the motion of the object is detected, regardless of whether the illumination is adequate or not.

6. Override Function

Quick switch ON/OFF 3 times within 2sec to override sensor function. Lights will switch on all the time. Power off and on again to recover sensor function.

7. Initialization

After power on, the sensor automatically turns on light at 100% brightness. After 10sec, it turns off the light. During the initialization, the sensor is not able to detect movement.

8. Factory settings

Detection Area: 100%, Hold Time: 5S, Daylight Sensor: Disable

9. Use Caution

1. Be sure to cut off the power supply before installing or adjusting the setting of the dial switch.

2. The microwave cannot pass through the metal, make sure there are no metal above the sensor.

3. It has to be at least 3.5mm away from metal around the microwave antenna. It is not allowed to place antenna and metal on the same horizontal.

Product Tags:


*From:	Your email address is incorrect!
*To:	Shenzhen Merrytek Technology Co., Ltd.
*Subject:	Subject is empty!
*Message:	For the best results, we recommend including the following details: -Self introduction -Required specifications -Inquire about price/MOQ Characters Remaining: (0/3000) Please enter 20 to 3000 characters to contact this supplier!

Categories	On Off Function Sensor
Brand Name:	Merrytek
Model Number:	MC090S E
Certification:	CE, TUV & RED
Place of Origin:	China
MOQ:	100pcs
Price:	Negotiation
Payment Terms:	T/T
Supply Ability:	100,000pcs per month
Delivery Time:	1, Sample and small order: Within 5 working days after receiving your payment. 2, Bulk order: 3-4 weeks after receiving deposit.
Packaging Details:	Packed in bubble bag firstly, and then reinforced with carton for outer packing
Rated Voltage:	220-240VAC 50/60Hz
Operating Frequency:	5.8 GHz ±74.9 MHz. ISM wave band
Working Mode:	ON/OFF Function
Mounting Height:	2.5-6 m
Lifetime:	5 years warranty @Ta 230V full load